BlackFire Products Instructions

Home/About Us Forums BBimpex Forum BlackFire Products Instructions

This topic contains 0 replies, has 1 voice, and was last updated by Sanjay Sanjay 1 year, 5 months ago.

Viewing 1 post (of 1 total)
  • Author
    Posts
  • #113
    Sanjay
    Sanjay
    Keymaster

    sanjay said:

    April 7, 2012 9:45 PM

    BF Gloss Enhancing Polish:
    ——————————

    This polish wipes on and buffs off easily by hand.

    Apply a 50 paisa size amount of product to a dry
    applicator pad and wipe on the surface using small circular motions.

    Apply to one section at a time (i.e. 1/2 hood, fender etc.)

    Allow light film to dry, Buff residues with a clean Microfiber.

    If using a dual action, machine polisher like Porter Cable 7424, apply with a constant Pressure, White Polishing pad.

    Set the Porter Cable`s speed control between 3-1/2 and 4.

    Buff off Residues with a clean Microfiber.

     

    sanjay said:

    Joined: Nov 23, 2010
    Posts: 41

    April 7, 2012 10:13 PM

    BF Wet Diamond All Finish Paint Protection (AFPP):
    ———————————————————-

    BF-AFPP can be applied by hand or dual-action machine polisher (DA). It applies easily and buffs off uniformly even in climates of high heat and high humidity. You simply walk around your car wiping on and buffing off as you go.

    Hand Application Tips:
    ————————-

    A. Always use on a cool surface out of direct sunlight.

    B. Apply a 50 paisa size amount of product on a dry applicator pad and wipe on the surface using small circular motions. Allow AFPP to dry before buffing.

    C. Buff Haze with a clean Microfiber.

    Machine Application Tips:
    —————————–

    A. Place a 6-1/2 inch, Hi-Gloss, constant pressure, Red Concours Finishing Pad on a 6 inch hook & loop backing plate and attach to your 7424 DA.

    B. Work on a small area, 24 to 36 inches square, out of direct sunlight.

    C. Apply two 6 to 8 inch lines of AFPP directly to the paint surface.

    D. With the machine off, spread the sealant over the surface using the dry foam pad. This coats the foam pad & the paint with sealant.

    E. Place the Red, Concours Finishing Pad on the paint and turn the Machine on. Set the speed dial on the DA between 3-1/2 and 4.

    F. Work the pad over the surface in a back-and-forth motion and then an up-and-down motion. Apply until the sealant starts to dry. Cover one section of the vehicle at a time (i.e. the hood, a door, fender etc)

    G. Allow a haze to form, Hand Buff to a brilliant Shine with a Microfiber.

     

    sanjay said:

    Joined: Nov 23, 2010
    Posts: 41

    May 27, 2013 7:05 PM

    BlackFire Wet Diamond Rinseless Wash –

    Washing:
    ———-

    -Dilute 1 ounce in 2 gallons of water. Soak a wash mitt or sponge in the solution and wash the vehicle one section at a time. Wash one panel at a time, making sure to flood the surface with an adequate amount of solution. Wash in gentle straight-line motions. Dry using two towels. Lightly wipe the first towel over the panel then follow with the second towel to ensure a high gloss, streak-free shine.

    Water conditioner:
    ——————–
    – Add 1-2 ounces to 3-5 gallons of wash water for additional lubrication. Wash and rinse as usual.

    Clay and buffing pad lubricant:
    ———————————-
    – Mix 2 ounces with 32 ounces of water in a clean spray bottle. Mist pads prior to use. Mist vehicle surfaces prior to using detailing clay.

    Quick detailer:
    —————-
    – Add 3 ounces to 32 ounces of water in a clean spray bottle. Mist and wipe paint with a soft microfiber towel.

    -Taken from Autogeek.net

     

     

Viewing 1 post (of 1 total)

You must be logged in to reply to this topic.